Manual Operation Automatic Pipe Bending Machine For Recovery Appliance Processing

Recovery appliance processing automatic tube bending machine with manual operation

-- Description of machine

The traditional two-dimensional bending machine has been unable to meet the needs of modern and complex industries. The three-dimensional pipe bending machine is gradually developed in this context. The application of programmable design controller in the bending machine control system provides technical assurance for the complex bending pipe system. Our pipe bending machine is very convenient to use, and can be quickly and skillfully used. It can be operated without deliberate training. It can carry out three-dimensional three-dimensional bending pipe processing methods. Only the input of the coordinate size can realize the simulation of bending pipe processing. For a variety of complex pipe bending operations, our pipe bending machine can easily and quickly change the processing mode, can perform memory editing, make the processed data archived so that it can be used directly next time, with high-speed operating efficiency.

-- Mechanical features

1. PLC control and the machine runs steadily.

2. It has various functions can be chosen, such as manual operation, automatic, semi-circulation, full-circulation and others.

3. Two angle setting, 0° to 185° is chosen at will. It can choose an angle or two angles continuously.

4. Mobile type foot switch with three functions, auto start, emergency stop, going on after emergency stop.

5. The safety is high.

6. Large volume cooling circulation system to make the machine run more steadily.

-- Installation points

1. Bending die installation

Plunge the elbow in a clockwise direction and cap it. Replace the required elbow wheel die and tighten the cap.

2. Clamp mold installation

Insert the clamping die with adjusting bolts, adjusting plates and cover plates into the clamping die holder and connect the adjusting bolts. The clamping die of the adjusting plate, cover plate, etc. is inserted into the clamping die holder and the adjusting plate is inserted. Fix on the clamp mold base and rotate the adjusting bolt so that the center of the clamp mold and the center of the bend tube mold are on the same plane. Then adjust it as follows:

2. 1.Loosen the clamping bolts and press the manual “Pinch” button until the clamped mold reaches the end point (there is a gap between the bending tube mold and the clamping mold).

2. 2.Adjust the clamping mold seat adjustment screw so that the clamping mold and the bending tube mold are fully compressed.

2. 3.Press the “Retreat” button to retract the clamping mold, and then turn the clamping mold adjustment screw into about 1/4-1/2 turns.

2. 4.Lock the clamping block fixing bolt.

3. Skateboard die adjustment method ditto

4. Mandrel and cylinder installation

4. 1.Screw the mandrel onto the mandrel screw and fix the mandrel to the proper position to fix the nut.

4. 2.Relax the mandrel cylinder bolts.

4. 3.The pointer of the moving mandrel cylinder block is related to the scale of the rail holder and the radius of the elbow.

4. 4.Lock the mandrel and cylinder.

5. Anti-crease device

The wrinkle-resistance mold is mounted on the wrinkle-proof plate seat, and it can be properly adjusted as shown in the figure by 1° to 2°.

6. Bending angle adjustment

The bend angle control is controlled by a proximity switch, a scale display is shown at the adjustment position of the proximity switch, and the proximity switch adjustment block is adjusted to a desired angle. Above is the first angle, below is the second angle, corresponding to the angle/double angle selection on the operation panel, after the trial bend and then trim the angle. Because the material of the pipe is different, the rebound amount is also different. After the adjustment is completed, the locking screw lock nut on the nut will be adjusted.

7. Overflow valve pressure adjustment

Press any of the manual buttons of pinch tube, back clamp, core, and back core to release the pressure displayed on the pressure gauge. At this time, rotate the pressure relief handle of the overflow valve to adjust the pressure to the desired pressure of 10 MPA. The bending resistance should not be too high, so as not to increase the oil temperature and to accelerate the wear of hydraulic components.

-- Main application

Recommended application industry: automobile fittings, oil pipe for brake, muffler, seats, motorcycle fittings, healthy equipment, air-conditioning, bicycle, steel furniture, sanitary wares, automobile fittings, brake lever, silencer, seats, motorcycle, body-building equipment, air conditioner, bicycle, steel-made furniture, sanitation equipment and other manufacturing trades.

Adapted material: steel pipe, stainless steel, copper pipe, aluminum pipe; rectangle pipe, square pipe, round pipe, round bar, square bar.

-- Specifications of machine

-- Packaging and service

1. Payment terms: 30% T/T down payment and 70% T/T before shipment.

2. Delivery time: No later than 15 days since receiving the advance payment.

3. Validity of the price: For ONE month.

4. Package: Wooden case.

5. Warranty period: We guarantee machine quality for 12 months. During this period, if spare parts of the machine were damaged, we can send the component to the customer by international express service freely.

6. We can send our engineers to the customer’s factory to install and train for using freely. The customers just need to provide the double trip tickets, food and accommodation for our engineers. The customer can also send your staff to our factory to learn the operation and maintains freely.

7. Our factory provides service for customers forever, if the customer needs operation help or technical guidance, you can contact us by Email or telephone at any time, we provide 24 hours on-line service.

-- Pictures of machine

►Zhangjiagang Huipu Machinery Manufacturing Co., Ltd established in 2002, is one of the professional manufacturers in pipe bending machines in Jiangsu province, China. Our company occupies a total area of 2000 sqms, and has a group of technicians.

►We are specializing in research, development and manufacturing of NC, CNC pipe bending machines, metal tube cutting machines, pipe end forming machines and other kinds of pipe processing machineries and equipments.

►Our company meets the requirements of furnitures, sports equipments, auto parts and other industries offering machines and processing tube products as well. We also design and manufacture machines of special specification according to customer requirements, as well as various kinds of non-standard machineries and equipments.

►Our company sincerely provides better services for new and original customers by virtue of advanced technologies, excellent quality control and competitive prices.